Search found 70 matches
- Wed Feb 07, 2024 3:49 pm
- Forum: Drivetrain
- Topic: Cat 3126B Flash Code 55
- Replies: 2
- Views: 1209
Re: Cat 3126B Flash Code 55
As you were driving had you used the cruise system or tried to use while it was flashing. did cruise work?. I had noticed that some other of my switches have gotten "less functional" shall I say. Dust in the contacts, carbon build up. Call it as you will. With the ignition OFF I rapidly sw...
- Mon Jan 29, 2024 10:08 am
- Forum: Drivetrain
- Topic: Mystery Oil pressure switch '98 Serengeti 3706
- Replies: 10
- Views: 3278
Re: Mystery Oil pressure switch '98 Serengeti 3706
There you go, my 1996 "1WM" 3126 Cat (with the 40 pin ECM) doesn't have that switch as I am sure that I have only "T" at the end as yours must be a 3126B series with a different serial number prefix. Good find, best of luck
- Tue Jan 23, 2024 8:07 am
- Forum: Drivetrain
- Topic: Mystery Oil pressure switch '98 Serengeti 3706
- Replies: 10
- Views: 3278
Re: Mystery Oil pressure switch '98 Serengeti 3706
I have traced my hourmeter wire back to the blue isolator in between the alternator and batteries and have a fused (5amp) connector on the center post. Note that hourmeters typically hook to either a pressure switch or ignition source and isolator is energized when alternator is running/ engine on!
- Sat Jan 20, 2024 1:02 pm
- Forum: Drivetrain
- Topic: Mystery Oil pressure switch '98 Serengeti 3706
- Replies: 10
- Views: 3278
Re: Mystery Oil pressure switch '98 Serengeti 3706
Scroll down to the bottom of the datcon page I have posted and click "go back" and all the gauges will pop up with part numbers and visuals less the Magnum word
- Sat Jan 20, 2024 12:57 pm
- Forum: Drivetrain
- Topic: Mystery Oil pressure switch '98 Serengeti 3706
- Replies: 10
- Views: 3278
Re: Mystery Oil pressure switch '98 Serengeti 3706
Sorry mine say Magnum as well and they are Datcon brand gauges and senders/sensors. I got my replacement oil senders from NWRV Supply, about $15 but if you look elsewhere on line look up Datcon as the gauge and sender must match by name and gauge pressure. Look here for the part numbers https://c-a-...
- Fri Jan 19, 2024 1:00 pm
- Forum: Electrical & Electronics
- Topic: Solar tutorial
- Replies: 1
- Views: 1708
Re: Solar tutorial
Handy Bob maybe
- Fri Jan 19, 2024 12:58 pm
- Forum: Drivetrain
- Topic: Mystery Oil pressure switch '98 Serengeti 3706
- Replies: 10
- Views: 3278
Re: Mystery Oil pressure switch '98 Serengeti 3706
If it has a single wire on it,someone replaces the sensor for either the dash or service bay oil pressure gauge. Each has their own sensor/ sender. I have replaces both mine with the appropriate sender. There are matching ones to the dash. ie" 0-100psi for the Datcon marked with Safari gauge, 0...
- Mon Jan 08, 2024 8:55 am
- Forum: Drivetrain
- Topic: fuel filters?
- Replies: 7
- Views: 208723
Re: fuel filters?
I own a Cat engine so I use Cat filters. That said, WHEN I own a "Baldwin" or "Fleetguard" engine I will use theirs. OH! they don't have an engine! They also say "Beyond Meat" tastes like meat!!......no it does not! That head mechanic of yours probably does not drive an...
- Sun Jan 07, 2024 1:41 pm
- Forum: Chassis
- Topic: Pacbrake issues
- Replies: 9
- Views: 343530
Re: Pacbrake issues
My '96 Geti has a tank (blue) forward of my front entry Kwikee steps. Easier to get to with the steps out but easy to see when I crawl under on my back. Maybe you should look a bit harder. I also drained "said" tank by removing one of the lowest air lines and there was a bunch of water and...
- Mon Jan 01, 2024 7:11 pm
- Forum: Interior
- Topic: Replace ceiling carpet ( headliner) with 1x4 Cedar TNG
- Replies: 2
- Views: 17063
Re: Replace ceiling carpet ( headliner) with 1x4 Cedar TNG
Basically a wood roof structure, carpet is attached to thin luan plywood 1/8" thick. I would cut around the edge of the visible carpet and remove all carpet, obviously remove lights first. Then luan is attached to 3/4"thick plywood upright trusses, you will be able to see the luan stapled ...