Search found 11 matches
- Fri Dec 29, 2023 9:42 am
- Forum: Electrical & Electronics
- Topic: Preignition dash light not coming on
- Replies: 2
- Views: 12730
Re: Preignition dash light not coming on
Hi Tom, You mentioned that "everything else in the startup sequence appears operational." Does this include the Check Engine light illuminating for 3 to 5 seconds after "Key-On"? If the Check Engine light does not illuminate when the key is switched on, the ECM isn't powered up. ...
- Tue Aug 22, 2023 6:38 pm
- Forum: Drivetrain
- Topic: fuel tank access
- Replies: 10
- Views: 87506
Re: fuel tank access
Hi Robert, Here is some information on the Winn Racor filter/water separators that were installed in our rigs that may be of help. Parker now supplies filters and support for these units. Sometime in the early 2000s when the original Racor 90S1230C filter elements became obsolete, Parker supplied an...
- Thu Jun 29, 2023 10:57 am
- Forum: Start Here
- Topic: Overheating continues
- Replies: 20
- Views: 39438
Re: Overheating continues
Hi Greg, As Brett mentioned, most of us have the direct belt drive fan so we aren't familiar with the fan clutch you have. If you can provide us with your engine serial number we should be able to look it up on the CAT parts website. If the fan clutch was originally supplied by CAT, the parts should...
- Tue Jun 14, 2022 8:40 pm
- Forum: Chassis
- Topic: Shop in the PNW for Magnum Chassis?
- Replies: 12
- Views: 7355
Re: Shop in the PNW for Magnum Chassis?
I had chassis work done at Gitt's Spring in Auburn WA several years ago. King pin replacement, overhaul of the steering box, and alignment. It is a small shop with a very dedicated staff. I was pleased with the work and the charges seemed reasonable.
- Tue Aug 17, 2021 12:32 pm
- Forum: Start Here
- Topic: hot skin condition?
- Replies: 2
- Views: 2914
Re: hot skin condition?
Hi Mel, If you are plugged into shore power, the coach chassis, skin, and AC electrical system ground should all be bonded together and through your power cord to a local ground rod. You might want to verify that you have continuity from the coach ground system, or the washer/dryer receptacle ground...
- Tue Aug 03, 2021 11:51 pm
- Forum: Start Here
- Topic: Clean rear radiator
- Replies: 20
- Views: 13373
Re: Clean rear radiator
Hello all, I've been following this thread with much interest. Keeping the radiator and the CAC clean is critical for proper engine cooling. Because of the radiator location, all the debris kicked up by six tires is then sucked up by the cooling fan and forced through the CAC and radiator. So keepin...
- Fri May 14, 2021 10:55 pm
- Forum: Electrical & Electronics
- Topic: Backup Camera replacement recommendations?
- Replies: 4
- Views: 4536
Re: Backup Camera replacement recommendations?
Hi Joey, I replaced my failing B&W monitor about two years ago with this system from Amazon: https://www.amazon.com/LeeKooLuu-Trailer-Monitor-Reversing-Waterproof/dp/B0761MM7YV/ref=sr_1_14?dchild=1&keywords=leekooluu+rv+backup+camera&qid=1621051018&sr=8-14 This system isn't wireless,...
- Fri Apr 30, 2021 2:22 pm
- Forum: Chassis
- Topic: Ride quality improvement after torsilastic spring replacement
- Replies: 5
- Views: 4852
Re: Ride quality improvement after torsilastic spring replacement
Rick & Bob,
Thank you both for your responses. Bob, wish you the best with all your renovation projects. Rick, can you tell me which type/part nmberHelwig air springs you installed?
Glenn Barney
'97 Coneinental 4006, CAT 3126
Thank you both for your responses. Bob, wish you the best with all your renovation projects. Rick, can you tell me which type/part nmberHelwig air springs you installed?
Glenn Barney
'97 Coneinental 4006, CAT 3126
- Wed Apr 21, 2021 6:03 pm
- Forum: Chassis
- Topic: Ride quality improvement after torsilastic spring replacement
- Replies: 5
- Views: 4852
Ride quality improvement after torsilastic spring replacement
I would be interested in feedback from anyone that has either replaced the torsilastic springs on their rig, or installed supplemental air spring kits such as offered by Pioneer Metal Works. My primary interest is improvement in ride quality, although I understand this is very subjective. I have all...
- Sun Nov 01, 2020 6:05 pm
- Forum: Drivetrain
- Topic: 96 Sahara 3126 fan blade needed
- Replies: 15
- Views: 10739
Re: 96 Sahara 3126 fan blade needed
I’ve just finished replacing my destroyed radiator fan while stranded in Pahrump NV. In the process I’ve discovered a few things that may be helpful to others in the future, so I’m posting this to pass the information along. My fan was destroyed because the four 8mm bolts that attach the fan bearing...